|
Introduction
|
The source of heat for outdoor space is solar
radiation. This radiation is received in three forms. Short wave
radiation such as ultraviolet, is largely intercepted by the
atmosphere.
The second form is the visible part of the spectrum that we experience
as light. This is direct solar radiation.
The third form is long wave or infrared radiation. This is
sometimes called terrestrial radiation because it is radiated from the
earth and all objects warmed by the sun.
|
Radiation
Solar Radiation
Transmitted solar radiation
Summer Sun
Double Glazing to reduce heat loss
|
Objects reflect, absorb or transmit direct solar
radiation. Each material in the environment responds differently in
each of these three categories. For example, typical glass reflects
some radiation, absorbs a small amount and transmits a great deal of direct solar
radiation.
Glass transmits the visible spectrum of radiation but not long wave
radiation. This is called the greenhouse effect and explains why
glass enclosed spaces gain heat when exposed to sunlight. The
visible light enters through the glass and is converted into long wave
radiation that is trapped inside the space because it is not transmitted
back out through the glass.
Visible light radiation is at least partially absorbed by objects
inside buildings and in the environment. This absorbed radiation is
reradiated as long wave radiation (heat). This natural principle is
the central tool used in the passive heating of buildings.
Double glazing should be considered for all
windows for energy efficiency and comfort in cool and temperate climates. In
warm climates, double, tinted, or reflective glass should be considered,
depending upon building size and use.
|
Radiation and Building Orientation
Summer Sun
Winter Sun
|
In the upper latitudes the south side
of a building receives nearly twice as much radiation in winter as in summer.
This effect is even more pronounced at the lower latitudes, where the ratio is
about one to four.
Also, in the upper latitudes, the east and west sides receive
about 2 1/ 2 times more radiation in summer than in winter. This ratio is not as
large in the lower latitudes; but it is noteworthy that in summer these sides
receive two to three times as much radiation as the south elevation.
In the
summer the west exposure is more disadvantageous than the east exposure, as the
afternoon high temperatures combine with the radiation effects. In all latitudes
the north side receives only a small amount of radiation, and this comes mainly
in the summer.
The amount of radiation received on a
horizontal roof surface exceeds all other sides.
Orientation: Conclusions
1. The optimum orientation will lie near the south; however, will differ
in the various regions, and will depend on the daily temperature distribution.
2. In all regions an orientation eastward from the south gives a better
yearly performance and a more equal daily heat distribution. Westerly directions
perform more poorly with unbalanced heat impacts.
3. The thermal orientation exposure has to be correlated with the local
wind directions.
|
Conduction and Convection
|
Conduction
|
Terrestrial radiation is transferred to the air and other
objects by conduction or convection. Conduction is the transfer of
energy through the direct contact of molecules. Those that are warm
vibrate at a faster rate than cooler ones. The activity of the
warmer molecules is physically transmitted to the cooler ones.
An electric burner on a stove transfers heat to a pot using this
principle. Each building material has a unique heat conductivity
rate.
Materials vary in their capacity to gain, store and radiate heat.
This is an important factor when selecting materials for microclimate
benefits. If a bench is to be used in the early morning, a material
that is slow to gain heat, and radiate it, would be a poor choice.
In the images at left, the iron bench would quickly gain and radiate heat
in the sun but would be very cold if not exposed to solar radiation.
The stone bench is a heat sink during the day. It absorbs heat
slowly for later radiation. It would be a good choice for an evening
sitting area.
The wood bench is more neutral. It does not absorb or radiate
much heat. It is a more comfortable surface in the morning before solar
radiation strikes the seating.
|
Iron
Stone
Wood
|
Convection
|
Convection is the transfer of heat from one object to
another through a fluid intermediary such as air. A breeze that pulls
heat from walls in a building demonstrates convection as a cooling
technique.
|
Albedo
|
Each material has a particular albedo. This is the
capacity of the material to reflect solar radiation. In general, the
color of a material is an indicator of its albedo. Black asphalt has
a low albedo and absorbs a great deal of light and heat compared to light gray
concrete. In this image the color of the building material reflects
light. Combined with a white roof, there is significant reduction in
interior heat gain. However, the reflected light into outdoor use
areas in the sun would raise the temperature significantly.
In this image, closely spaced buildings of high mass walls, and
balconies shade windows and exterior space to limit heat gain.
|
|
|
Direct solar radiation provides many watts per square foot. |
|
In this illustration, direct solar radiation is counteracted by
the evaporative cooling of the water. Water or perspiration on the
skin absorbs heat that is removed as the water evaporates. Air
temperatures adjacent to water bodies such as lakes or the ocean are moderated - lower in the day and
higher at night. |
Shading Devices
|
The most effective control of heat gain in buildings is the
shading of windows with the use of exterior shading devices. In this
example, shutters with movable louvers block direct solar radiation.
The louvers are adjusted to block the sun at anytime of day while
permitting airflow into the building. Opening the shutters when the
windows are not exposed to sun permits maximum air flow and convective
cooling of interior building surfaces.
These principles apply to exterior spaces, also.
|
|
|
Combining protection from wind, light reflecting surfaces
and material that gain, store and reradiate heat would create an outdoor
microclimate that would be desirable in the late afternoon in the spring
or fall when temperatures are moderate or during the day in the winter.
Other combinations of breeze control, materials, shading and solar
orientation can be combined to create other microclimates.
|
Filoli in California
|
Study this image. Assume that the windows shown face
south. What are the processes and materials that create the micro
climate for this space? At which time of the day would this space be
most comfortable in summer? At which time of the day would this
space be most comfortable in winter?
|
Ira's Fountain, Portland, Oregon
|
Water is a very effective moderator of air temperature
because is requires a great deal of energy to raise or lower the
temperature of water. Therefore, water is generally cooler than the
air temperature during the day and higher at night. This inverse
relationship tends to buffer wide swings in daily air temperature in areas
adjacent to large volumes of water. Evaporative cooling is a second
effective way that people and objectives are cooled through the
interaction with water. Evaporative cooling is most effective when
the humidity is low.
|
Plants and Heat Control
|
Trees, shrubs and turf influence microclimates
in several ways. The leaves of trees reflect or absorb much solar
radiation. A small amount of visible radiation is transmitted
through the leaves. Long wave or terrestrial radiation comes from
the leaves and branches, moderating diurnal temperature extremes. Tree
canopies prevent some long wave radiation from escaping at night further
moderating temperature swings.
The
humidity is higher under a tree canopy in part because moisture is
retained under the ceiling-like canopy. Trees, shrubs and turf
transpire moisture as a cooling strategy. This increases the
humidity and provides for evaporative cooling of the air and objects in
the microclimate.
|
|
Berms
|
Berms are earth mounds that can produce
microclimate effects by diverting wind or acting as thermal sinks.
Similarly, earth behind retaining walls or building walls help to buffer the
site and building against
temperature extremes of both heat and cold.
The planting on earth berms also
provides evaporative cooling near the building. Earth berms can be a building construction
cost savers because the foundation does not have to be as deep (in
single-storied construction); the earth and ground cover is often less costly
than other wall finishing materials. Its long-term maintenance can also be lower
than conventional materials.
Architectural GRAPHIC Standards CD-ROM
John Wiley & Sons, Inc. New York, NY
|
Planted Retaining Wall
|
|
The images at left illustrate a range of
microclimates. Most of the spaces shown are a combination of more
than one microclimate based on heat reduction or accumulation. Study
these in reference to the material above and that in the previous tutorial
on wind. Note how the microclimates are created and incorporate
similar microclimate areas in your schematic design assignment. |
|
|